An injection molding machine melts plastic pellets, injects them into a closed mold under pressure, cools the part, and ejects it. Everything it does is split between two systems: an injection unit that melts and delivers the resin, and a clamping unit that holds the mold shut while the cavity fills. Each component in those two units affects cycle time, part quality, tooling requirements, and cost.

This guide walks through every main part of the machine, how one molding cycle runs, how clamp tonnage is sized from part geometry, and how machine and mold choices change your quote. At Jaycon we use this to match each part to the right machine, material, mold, and finishing before production begins.

The main parts of an injection molding machine

The machine has two working units mounted on a bed. The injection unit melts and shoots the resin; the clamping unit opens, closes, and holds the mold. The diagram below shows where each part sits.

A side schematic of an injection molding machine, with the injection unit of hopper, barrel, reciprocating screw, heater bands and nozzle on the left feeding melt into the mold, and the clamping unit of fixed platen, cavity and core, moving platen, tie bars and ejector on the right
The injection unit and the clamping unit, with every main part labeled.
ComponentFunctionWhy it matters
HopperFeeds plastic pellets into the barrelResin drying and feed consistency affect defects
Barrel and reciprocating screwMelts, mixes, and pressurizes the resinSets melt quality, shot size, and cycle stability
Heaters and thermocouplesHold the barrel temperature zonesPrevent burns, short shots, and inconsistent viscosity
NozzleTransfers melt into the mold sprueMust match the mold sprue and the resin
Mold: cavity and coreForms the final part geometryDefines parting line, draft, ejection, and finish
Clamping unitOpens, closes, and holds the mold shutResists injection pressure so the part does not flash
Platens and tie barsSupport and guide the mold during clampingSet the largest mold size and daylight the machine accepts
Ejector systemPushes the cooled part out of the moldPrevents sticking, distortion, and cosmetic damage
Drive: hydraulic, electric, or hybridPowers injection, clamping, and plasticizingAffects energy use, speed, precision, and maintenance
Control systemManages temperatures, pressures, speeds, and timingEnables repeatability and process monitoring

The injection unit

The injection unit is where plastic becomes a melt. Pellets drop from the hopper into a heated barrel, where a reciprocating screw turns to melt, mix, and meter the resin, then drives forward like a plunger to inject it. Heater bands and thermocouples hold each barrel zone at its set temperature, and the nozzle seals against the mold so the melt passes into the sprue without leaking.

The clamping unit

The clamping unit carries the mold and keeps it closed against the pressure of the incoming melt. The fixed platen and the moving platen each hold one mold half, the tie bars guide the moving platen and carry the clamp load, and the ejector system pushes the finished part off the core once the mold opens. The clamp force the unit can hold, and the space between its tie bars, decide which molds fit the machine.

How the injection molding cycle works

One shot runs through the same six stages every time. The cycle repeats for every part, so small savings in any stage add up across a production run.

A six stage loop of the injection molding cycle: clamp, inject, pack and hold, cool, eject and post-process, returning to the next shot
The six stages of one molding cycle, looping back to the next shot.
  1. Clamp: the moving platen closes the mold and applies clamp force.
  2. Inject: the screw pushes molten resin through the nozzle and runner into the cavity.
  3. Pack and hold: added pressure compensates for the material shrinking as it cools.
  4. Cool: the part solidifies in the mold; cooling is often the largest share of cycle time.
  5. Open and eject: the mold opens and ejector pins remove the finished part.
  6. Post-process: the part is degated, inspected, finished, assembled, or packaged.

Because cooling dominates the cycle, wall thickness and cooling line design do more for throughput than raising injection speed. That is one of the things a design review checks before a tool is cut.

Clamp tonnage: how to size the machine to the part

Clamp tonnage is the force that keeps the mold closed while the cavity fills. Too little and the mold blows open and the part flashes; far too much and you are paying for a bigger machine than the job needs. It starts from the projected area, the part’s shadow on the parting line, plus the runner, multiplied by a material factor.

A diagram showing projected area as the molded part's shadow on the parting line under cavity pressure, with the clamp tonnage formula of projected area times material factor times safety margin at about 3 to 5 tons per square inch
Projected area is the part’s shadow on the parting line; clamp tonnage scales with it and the cavity pressure.

Required clamp tonnage = total projected area × material tonnage factor × safety margin. For a multi-cavity mold, use the projected area of all cavities plus the runner: total projected area = (part area × number of cavities) + runner area. Typical factors run about 3 to 5 tons per square inch of projected area, depending on the material, flow, wall thickness, and process.

Quick clamp tonnage reference

Part sizeApprox. projected area1 cavity at 3 to 5 tons/in²2 cavity at 3 to 5 tons/in²
1 in × 1 in1 in²3 to 5 tons6 to 10 tons
2 in × 2 in4 in²12 to 20 tons24 to 40 tons
3 in × 3 in9 in²27 to 45 tons54 to 90 tons
4 in × 4 in16 in²48 to 80 tons96 to 160 tons
6 in × 6 in36 in²108 to 180 tons216 to 360 tons
8 in × 8 in64 in²192 to 320 tons384 to 640 tons

These assume a simple flat part, no unusually thin walls, and a basic runner. Add a safety margin of roughly 10 to 20%, then confirm the machine’s tie-bar spacing, shot capacity, and mold dimensions also fit the tool.

Material tonnage factors

Material familyTypical tonnage factorNotes
Polypropylene (PP)3 to 4 tons/in²Free flowing; generally a lower clamp requirement
ABS3 to 5 tons/in²Common for consumer and electronics housings
Polycarbonate (PC)4 to 5 tons/in²Higher viscosity and stiffness
Nylon / PA4 to 5+ tons/in²Sensitive to moisture, shrinkage, and process
Glass filled resins5+ tons/in²Higher viscosity and abrasiveness; may need more clamp force

Aluminum vs. steel molds

A common search, “aluminum molding machine,” usually means the mold, not the machine: an aluminum injection mold running plastic parts on a standard machine. Aluminum molds are CNC machined, cost less, and are ready faster than hardened steel, which makes them a strong fit for prototype, bridge, and lower-volume production while a design is still being validated.

Two injection mold halves on a stainless bench, a brushed aluminum core on the left and a darker hardened steel core on the right with water cooling fittings and ejector pin holes
A brushed aluminum mold half on the left and a darker hardened steel mold half on the right, two tooling choices for the same part.
Tooling optionBest forAdvantagesLimitations
Aluminum moldPrototypes, bridge production, design validationFaster lead time, lower cost, easier changesShorter tool life, lower wear resistance
Pre-hardened steel moldModerate volumes and production validationBetter durability and dimensional stabilityHigher cost, longer machining time
Hardened steel moldHigh-volume productionLong tool life, repeatable quality, high cavitationHighest upfront cost and longest lead time

Treat aluminum tooling as a bridge strategy: it lowers early risk and lets you test material, finish, assembly, and market response before committing to long-run steel. For how the two compare on tool life and cost, see our guide to aluminum vs. steel tooling.

Post-processing after molding

Post-processing is every operation after the part leaves the mold. It can improve appearance, remove excess material, add markings, prepare parts for assembly, or meet quality documentation. It often costs less than adding a complex mold action, changing material, or redesigning a part just to avoid a secondary step.

A gloved hand deburring a molded plastic enclosure on a steel bench, with flush cutters, a finishing fixture, and a tray of brass threaded inserts nearby
Deburring a molded enclosure at a finishing bench, with flush cutters and brass threaded inserts ready for assembly.
  • Degating: removes the gate or runner remnant from the part.
  • Deflashing: removes thin excess plastic along the parting line.
  • Machining: adds or refines features that are hard to mold, such as precise holes or tight tolerances.
  • Insert installation: adds threaded metal inserts, often by heat staking or ultrasonic insertion.
  • Painting and coating: improves appearance, UV resistance, conductivity, or surface protection.
  • Pad printing and laser marking: adds logos, warnings, serial numbers, or regulatory marks.
  • Ultrasonic welding: joins plastic parts without adhesives or fasteners.
  • Inspection and documentation: verifies critical dimensions and supports quality requirements.

How to choose the right machine and mold

Before locking in a machine, confirm the part, the resin, and the tool agree on all of these:

  • Clamp tonnage: from total projected area, resin, cavity count, and runner.
  • Shot size: the machine must melt and inject enough for all parts and runners.
  • Tie-bar spacing: the mold has to physically fit between the tie bars.
  • Platen size and daylight: the mold must open far enough for part removal and automation.
  • Screw and barrel compatibility: matters for filled, corrosive, high-temperature, or engineering resins.
  • Cycle-time target: cooling, injection, ejection, and robot handling all affect throughput.
  • Post-processing: plan degating, marking, assembly, and inspection into the quote.

Most of these are set long before the machine is chosen, at the design stage. A design for manufacturing review catches the ones that would otherwise force a mold change later.

Get a production-ready molding quote

Jaycon can review your CAD model, recommend the material and tooling strategy, size the molding requirements, and give you an itemized quote for tooling, molding, finishing, and assembly, all under one roof.

Ready to move from design to molded production parts? Request a quote, or talk through the tooling path first with our guide to when to stop 3D printing and start tooling.

Related reading